From 7a4a3503d50819a199f0d73f28d2b2a4c66f459a Mon Sep 17 00:00:00 2001 From: Tom Rini Date: Jun 12 2018 11:26:15 +0000 Subject: Merge git://git.denx.de/u-boot-marvell --- diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 790571b..3dcd6dd 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -91,6 +91,7 @@ dtb-$(CONFIG_ARCH_MVEBU) += \ armada-375-db.dtb \ armada-388-clearfog.dtb \ armada-388-gp.dtb \ + armada-388-helios4.dtb \ armada-385-amc.dtb \ armada-7040-db.dtb \ armada-7040-db-nand.dtb \ diff --git a/arch/arm/dts/armada-388-helios4.dts b/arch/arm/dts/armada-388-helios4.dts new file mode 100644 index 0000000..049d322 --- /dev/null +++ b/arch/arm/dts/armada-388-helios4.dts @@ -0,0 +1,314 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Device Tree file for Helios4 + * based on SolidRun Clearfog revision A1 rev 2.0 (88F6828) + * + * Copyright (C) 2017 Aditya Prayoga + * + */ + +/dts-v1/; +#include "armada-388.dtsi" +#include "armada-38x-solidrun-microsom.dtsi" + +/ { + model = "Helios4"; + compatible = "kobol,helios4", "marvell,armada388", + "marvell,armada385", "marvell,armada380"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x80000000>; /* 2 GB */ + }; + + aliases { + /* So that mvebu u-boot can update the MAC addresses */ + ethernet1 = ð0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + reg_12v: regulator-12v { + compatible = "regulator-fixed"; + regulator-name = "power_brick_12V"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + regulator-always-on; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + vin-supply = <®_12v>; + }; + + reg_5p0v_hdd: regulator-5v-hdd { + compatible = "regulator-fixed"; + regulator-name = "5V_HDD"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + vin-supply = <®_12v>; + }; + + reg_5p0v_usb: regulator-5v-usb { + compatible = "regulator-fixed"; + regulator-name = "USB-PWR"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + enable-active-high; + gpio = <&expander0 6 GPIO_ACTIVE_HIGH>; + vin-supply = <®_12v>; + }; + + system-leds { + compatible = "gpio-leds"; + status-led { + label = "helios4:green:status"; + gpios = <&gpio0 24 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + default-state = "on"; + }; + + fault-led { + label = "helios4:red:fault"; + gpios = <&gpio0 25 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + }; + + io-leds { + compatible = "gpio-leds"; + sata1-led { + label = "helios4:green:ata1"; + gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; + linux,default-trigger = "ata1"; + default-state = "off"; + }; + sata2-led { + label = "helios4:green:ata2"; + gpios = <&gpio1 18 GPIO_ACTIVE_LOW>; + linux,default-trigger = "ata2"; + default-state = "off"; + }; + sata3-led { + label = "helios4:green:ata3"; + gpios = <&gpio1 20 GPIO_ACTIVE_LOW>; + linux,default-trigger = "ata3"; + default-state = "off"; + }; + sata4-led { + label = "helios4:green:ata4"; + gpios = <&gpio1 21 GPIO_ACTIVE_LOW>; + linux,default-trigger = "ata4"; + default-state = "off"; + }; + usb-led { + label = "helios4:green:usb"; + gpios = <&gpio1 22 GPIO_ACTIVE_LOW>; + linux,default-trigger = "usb-host"; + default-state = "off"; + }; + }; + + fan1: j10-pwm { + compatible = "pwm-fan"; + pwms = <&gpio1 9 40000>; /* Target freq:25 kHz */ + }; + + fan2: j17-pwm { + compatible = "pwm-fan"; + pwms = <&gpio1 23 40000>; /* Target freq:25 kHz */ + }; + + usb2_phy: usb2-phy { + compatible = "usb-nop-xceiv"; + vbus-regulator = <®_5p0v_usb>; + }; + + usb3_phy: usb3-phy { + compatible = "usb-nop-xceiv"; + }; + + soc { + internal-regs { + i2c@11000 { + clock-frequency = <400000>; + pinctrl-0 = <&i2c0_pins>; + pinctrl-names = "default"; + status = "okay"; + + /* + * PCA9655 GPIO expander, up to 1MHz clock. + * 0-Board Revision bit 0 # + * 1-Board Revision bit 1 # + * 5-USB3 overcurrent + * 6-USB3 power + */ + expander0: gpio-expander@20 { + /* + * This is how it should be: + * compatible = "onnn,pca9655", + * "nxp,pca9555"; + * but you can't do this because of + * the way I2C works. + */ + compatible = "nxp,pca9555"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x20>; + pinctrl-names = "default"; + pinctrl-0 = <&pca0_pins>; + interrupt-parent = <&gpio0>; + interrupts = <23 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <2>; + + board_rev_bit_0 { + gpio-hog; + gpios = <0 GPIO_ACTIVE_LOW>; + input; + line-name = "board-rev-0"; + }; + board_rev_bit_1 { + gpio-hog; + gpios = <1 GPIO_ACTIVE_LOW>; + input; + line-name = "board-rev-1"; + }; + usb3_ilimit { + gpio-hog; + gpios = <5 GPIO_ACTIVE_HIGH>; + input; + line-name = + "usb-overcurrent-status"; + }; + }; + + temp_sensor: temp@4c { + compatible = "ti,lm75"; + reg = <0x4c>; + vcc-supply = <®_3p3v>; + }; + }; + + i2c@11100 { + /* + * External I2C Bus for user peripheral + */ + clock-frequency = <400000>; + pinctrl-0 = <&helios_i2c1_pins>; + pinctrl-names = "default"; + status = "okay"; + }; + + sata@a8000 { + status = "okay"; + #address-cells = <1>; + #size-cells = <0>; + + sata0: sata-port@0 { + reg = <0>; + }; + + sata1: sata-port@1 { + reg = <1>; + }; + }; + + sata@e0000 { + status = "okay"; + #address-cells = <1>; + #size-cells = <0>; + + sata2: sata-port@0 { + reg = <0>; + }; + + sata3: sata-port@1 { + reg = <1>; + }; + }; + + spi@10680 { + pinctrl-0 = <&spi1_pins + µsom_spi1_cs_pins>; + pinctrl-names = "default"; + status = "okay"; + }; + + sdhci@d8000 { + bus-width = <4>; + cd-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; + no-1-8-v; + pinctrl-0 = <&helios_sdhci_pins + &helios_sdhci_cd_pins>; + pinctrl-names = "default"; + status = "okay"; + vmmc = <®_3p3v>; + wp-inverted; + }; + + usb@58000 { + usb-phy = <&usb2_phy>; + status = "okay"; + }; + + usb3@f0000 { + status = "okay"; + }; + + usb3@f8000 { + status = "okay"; + }; + + pinctrl@18000 { + pca0_pins: pca0-pins { + marvell,pins = "mpp23"; + marvell,function = "gpio"; + }; + microsom_phy0_int_pins: microsom-phy0-int-pins { + marvell,pins = "mpp18"; + marvell,function = "gpio"; + }; + helios_i2c1_pins: i2c1-pins { + marvell,pins = "mpp26", "mpp27"; + marvell,function = "i2c1"; + }; + helios_sdhci_cd_pins: helios-sdhci-cd-pins { + marvell,pins = "mpp20"; + marvell,function = "gpio"; + }; + helios_sdhci_pins: helios-sdhci-pins { + marvell,pins = "mpp21", "mpp28", + "mpp37", "mpp38", + "mpp39", "mpp40"; + marvell,function = "sd0"; + }; + helios_led_pins: helios-led-pins { + marvell,pins = "mpp24", "mpp25", + "mpp49", "mpp50", + "mpp52", "mpp53", + "mpp54"; + marvell,function = "gpio"; + }; + helios_fan_pins: helios-fan-pins { + marvell,pins = "mpp41", "mpp43", + "mpp48", "mpp55"; + marvell,function = "gpio"; + }; + microsom_spi1_cs_pins: spi1-cs-pins { + marvell,pins = "mpp59"; + marvell,function = "spi1"; + }; + }; + }; + }; +}; diff --git a/arch/arm/dts/armada-38x-solidrun-microsom.dtsi b/arch/arm/dts/armada-38x-solidrun-microsom.dtsi new file mode 100644 index 0000000..a262722 --- /dev/null +++ b/arch/arm/dts/armada-38x-solidrun-microsom.dtsi @@ -0,0 +1,101 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Device Tree file for SolidRun Armada 38x Microsom + * + * Copyright (C) 2015 Russell King + * + * This board is in development; the contents of this file work with + * the A1 rev 2.0 of the board, which does not represent final + * production board. Things will change, don't expect this file to + * remain compatible info the future. + */ +#include +#include + +/ { + memory { + device_type = "memory"; + reg = <0x00000000 0x10000000>; /* 256 MB */ + }; + + soc { + ranges = ; + + internal-regs { + rtc@a3800 { + /* + * If the rtc doesn't work, run "date reset" + * twice in u-boot. + */ + status = "okay"; + }; + }; + }; +}; + +ð0 { + /* ethernet@70000 */ + mac-address = [00 50 43 02 02 01]; + pinctrl-0 = <&ge0_rgmii_pins>; + pinctrl-names = "default"; + phy = <&phy_dedicated>; + phy-mode = "rgmii-id"; + status = "okay"; +}; + +&mdio { + /* + * Add the phy clock here, so the phy can be accessed to read its + * IDs prior to binding with the driver. + */ + pinctrl-0 = <&mdio_pins µsom_phy_clk_pins>; + pinctrl-names = "default"; + + phy_dedicated: ethernet-phy@0 { + /* + * Annoyingly, the marvell phy driver configures the LED + * register, rather than preserving reset-loaded setting. + * We undo that rubbish here. + */ + marvell,reg-init = <3 16 0 0x101e>; + reg = <0>; + }; +}; + +&pinctrl { + microsom_phy_clk_pins: microsom-phy-clk-pins { + marvell,pins = "mpp45"; + marvell,function = "ref"; + }; + /* Optional eMMC */ + microsom_sdhci_pins: microsom-sdhci-pins { + marvell,pins = "mpp21", "mpp28", "mpp37", + "mpp38", "mpp39", "mpp40"; + marvell,function = "sd0"; + }; +}; + +&spi1 { + /* The microsom has an optional W25Q32 on board, connected to CS0 */ + pinctrl-0 = <&spi1_pins>; + + w25q32: spi-flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "w25q32", "jedec,spi-nor"; + reg = <0>; /* Chip select 0 */ + spi-max-frequency = <3000000>; + status = "disabled"; + }; +}; + +&uart0 { + pinctrl-0 = <&uart0_pins>; + pinctrl-names = "default"; + status = "okay"; + u-boot,dm-pre-reloc; +}; diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig index f431cff..5415b5a 100644 --- a/arch/arm/mach-mvebu/Kconfig +++ b/arch/arm/mach-mvebu/Kconfig @@ -75,6 +75,10 @@ config TARGET_CLEARFOG bool "Support ClearFog" select 88F6820 +config TARGET_HELIOS4 + bool "Support Helios4" + select 88F6820 + config TARGET_MVEBU_ARMADA_37XX bool "Support Armada 37xx platforms" select ARMADA_3700 @@ -132,6 +136,7 @@ endchoice config SYS_BOARD default "clearfog" if TARGET_CLEARFOG + default "helios4" if TARGET_HELIOS4 default "mvebu_armada-37xx" if TARGET_MVEBU_ARMADA_37XX default "db-88f6720" if TARGET_DB_88F6720 default "db-88f6820-gp" if TARGET_DB_88F6820_GP @@ -146,6 +151,7 @@ config SYS_BOARD config SYS_CONFIG_NAME default "clearfog" if TARGET_CLEARFOG + default "helios4" if TARGET_HELIOS4 default "mvebu_armada-37xx" if TARGET_MVEBU_ARMADA_37XX default "db-88f6720" if TARGET_DB_88F6720 default "db-88f6820-gp" if TARGET_DB_88F6820_GP @@ -166,6 +172,7 @@ config SYS_VENDOR default "Marvell" if TARGET_DB_88F6820_AMC default "Marvell" if TARGET_MVEBU_ARMADA_8K default "solidrun" if TARGET_CLEARFOG + default "kobol" if TARGET_HELIOS4 default "Synology" if TARGET_DS414 default "CZ.NIC" if TARGET_TURRIS_OMNIA default "CZ.NIC" if TARGET_TURRIS_MOX diff --git a/board/kobol/helios4/MAINTAINERS b/board/kobol/helios4/MAINTAINERS new file mode 100644 index 0000000..c9610de --- /dev/null +++ b/board/kobol/helios4/MAINTAINERS @@ -0,0 +1,6 @@ +HELIOS4 BOARD +M: Dennis Gilmore +S: Maintained +F: board/kobol/helios4/ +F: include/configs/helios4.h +F: configs/helios4_defconfig diff --git a/board/kobol/helios4/Makefile b/board/kobol/helios4/Makefile new file mode 100644 index 0000000..63f0796 --- /dev/null +++ b/board/kobol/helios4/Makefile @@ -0,0 +1,5 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright (C) 2018 Dennis Gilmore + +obj-y := helios4.o diff --git a/board/kobol/helios4/README b/board/kobol/helios4/README new file mode 100644 index 0000000..749f048 --- /dev/null +++ b/board/kobol/helios4/README @@ -0,0 +1,46 @@ +Update from original Marvell U-Boot to mainline U-Boot: +------------------------------------------------------- + +Generate the U-Boot image with these commands: + +$ make helios4_defconfig +$ make + +The resulting image including the SPL binary with the +full DDR setup is "u-boot-spl.kwb". + +Now all you need to do is copy this image on a SD card. +For example with this command: + +$ sudo dd if=u-boot-spl.kwb of=/dev/sdX bs=512 seek=1 + +Please use the correct device node for your setup instead +of "/dev/sdX" here! + +Boot selection: +--------------- + +Before powering up the board, boot selection should be done via the SW1 dip +switch (0: OFF, 1: ON): + + - SPI: 00010 + - SD/eMMC: 00111 + - SATA1: 11100 + - UART: 11110 + +Boot from UART: +--------------- + +Connect the on-board micro-USB (CF Pro: CON11, CF Base: CON5) +to your host. + +Set the SW1 DIP switches to UART boot (see above). + +Run the following command to initiate U-Boot download: + + ./tools/kwboot -p -b u-boot-spl.kwb /dev/ttyUSBX + +Use the correct UART device node for /dev/ttyUSBX. + +When download finishes start your favorite terminal emulator +on /dev/ttyUSBX. diff --git a/board/kobol/helios4/helios4.c b/board/kobol/helios4/helios4.c new file mode 100644 index 0000000..3416783 --- /dev/null +++ b/board/kobol/helios4/helios4.c @@ -0,0 +1,163 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2018 Dennis Gilmore + * based on board/solidrun/clearfog/clearfog.c + */ + +#include +#include +#include +#include +#include +#include +#include + +#include "../drivers/ddr/marvell/a38x/ddr3_init.h" +#include <../serdes/a38x/high_speed_env_spec.h> + +DECLARE_GLOBAL_DATA_PTR; + +#define ETH_PHY_CTRL_REG 0 +#define ETH_PHY_CTRL_POWER_DOWN_BIT 11 +#define ETH_PHY_CTRL_POWER_DOWN_MASK BIT(ETH_PHY_CTRL_POWER_DOWN_BIT) + +/* + * Those values and defines are taken from the Marvell U-Boot version + * "u-boot-2013.01-15t1-helios4" as well as the upstream config for clearfog + */ +#define BOARD_GPP_OUT_ENA_LOW 0xffffffff +#define BOARD_GPP_OUT_ENA_MID 0xffffffff + +#define BOARD_GPP_OUT_VAL_LOW 0x0 +#define BOARD_GPP_OUT_VAL_MID 0x0 +#define BOARD_GPP_POL_LOW 0x0 +#define BOARD_GPP_POL_MID 0x0 + +/* IO expander on Marvell GP board includes e.g. fan enabling */ +struct marvell_io_exp { + u8 addr; + u8 val; +}; + +static struct marvell_io_exp io_exp[] = { + {6, 0xf9}, + {2, 0x46}, /* Assert reset signals and enable USB3 current limiter */ + {6, 0xb9} +}; + +static struct serdes_map board_serdes_map[] = { + {SATA0, SERDES_SPEED_6_GBPS, SERDES_DEFAULT_MODE, 0, 0}, + {USB3_HOST0, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0}, + {SATA1, SERDES_SPEED_6_GBPS, SERDES_DEFAULT_MODE, 0, 0}, + {SATA3, SERDES_SPEED_6_GBPS, SERDES_DEFAULT_MODE, 0, 0}, + {SATA2, SERDES_SPEED_6_GBPS, SERDES_DEFAULT_MODE, 0, 0}, + {USB3_HOST1, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0}, +}; + +int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count) +{ + *serdes_map_array = board_serdes_map; + *count = ARRAY_SIZE(board_serdes_map); + return 0; +} + +/* + * Define the DDR layout / topology here in the board file. This will + * be used by the DDR3 init code in the SPL U-Boot version to configure + * the DDR3 controller. + */ +static struct mv_ddr_topology_map board_topology_map = { + DEBUG_LEVEL_ERROR, + 0x1, /* active interfaces */ + /* cs_mask, mirror, dqs_swap, ck_swap X PUPs */ + { { { {0x1, 0, 0, 0}, + {0x1, 0, 0, 0}, + {0x1, 0, 0, 0}, + {0x1, 0, 0, 0}, + {0x1, 0, 0, 0} }, + SPEED_BIN_DDR_1600K, /* speed_bin */ + MV_DDR_DEV_WIDTH_16BIT, /* memory_width */ + MV_DDR_DIE_CAP_8GBIT, /* mem_size */ + DDR_FREQ_800, /* frequency */ + 0, 0, /* cas_wl cas_l */ + MV_DDR_TEMP_LOW, /* temperature */ + MV_DDR_TIM_DEFAULT} }, /* timing */ + BUS_MASK_32BIT_ECC, /* Busses mask */ + MV_DDR_CFG_DEFAULT, /* ddr configuration data source */ + { {0} }, /* raw spd data */ + {0} /* timing parameters */ +}; + +struct mv_ddr_topology_map *mv_ddr_topology_map_get(void) +{ + /* Return the board topology as defined in the board code */ + return &board_topology_map; +} + +int board_early_init_f(void) +{ + /* Configure MPP */ + writel(0x11111111, MVEBU_MPP_BASE + 0x00); + writel(0x11111111, MVEBU_MPP_BASE + 0x04); + writel(0x10400011, MVEBU_MPP_BASE + 0x08); + writel(0x22043333, MVEBU_MPP_BASE + 0x0c); + writel(0x44400002, MVEBU_MPP_BASE + 0x10); + writel(0x41144004, MVEBU_MPP_BASE + 0x14); + writel(0x40333333, MVEBU_MPP_BASE + 0x18); + writel(0x00004444, MVEBU_MPP_BASE + 0x1c); + + /* Set GPP Out value */ + writel(BOARD_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00); + writel(BOARD_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00); + + /* Set GPP Polarity */ + writel(BOARD_GPP_POL_LOW, MVEBU_GPIO0_BASE + 0x0c); + writel(BOARD_GPP_POL_MID, MVEBU_GPIO1_BASE + 0x0c); + + /* Set GPP Out Enable */ + writel(BOARD_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04); + writel(BOARD_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04); + + return 0; +} + +int board_init(void) +{ + int i; + + /* Address of boot parameters */ + gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100; + + /* Init I2C IO expanders */ + for (i = 0; i < ARRAY_SIZE(io_exp); i++) { + struct udevice *dev; + int ret; + + ret = i2c_get_chip_for_busnum(0, io_exp[i].addr, 1, &dev); + if (ret) { + printf("Cannot find I2C: %d\n", ret); + return 0; + } + + ret = dm_i2c_write(dev, io_exp[i].val, &io_exp[i].val, 1); + if (ret) { + printf("Failed to set IO expander via I2C\n"); + return -EIO; + } + } + + return 0; +} + +int checkboard(void) +{ + puts("Board: Helios4\n"); + + return 0; +} + +int board_eth_init(bd_t *bis) +{ + cpu_eth_init(bis); /* Built in controller(s) come first */ + return pci_eth_init(bis); +} diff --git a/board/kobol/helios4/kwbimage.cfg b/board/kobol/helios4/kwbimage.cfg new file mode 100644 index 0000000..035063b --- /dev/null +++ b/board/kobol/helios4/kwbimage.cfg @@ -0,0 +1,13 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright (C) 2015 Stefan Roese +# + +# Armada 38x use version 1 image format +VERSION 1 + +# Boot Media configurations +BOOT_FROM sdio + +# Binary Header (bin_hdr) with DDR3 training code +BINARY spl/u-boot-spl-dtb.bin 0000005b 00000068 diff --git a/configs/helios4_defconfig b/configs/helios4_defconfig new file mode 100644 index 0000000..b724285 --- /dev/null +++ b/configs/helios4_defconfig @@ -0,0 +1,58 @@ +CONFIG_ARM=y +CONFIG_ARCH_MVEBU=y +CONFIG_SYS_TEXT_BASE=0x00800000 +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_SYS_MALLOC_F_LEN=0x2000 +CONFIG_TARGET_HELIOS4=y +CONFIG_SPL_MMC_SUPPORT=y +CONFIG_SPL_SERIAL_SUPPORT=y +CONFIG_SPL_LIBDISK_SUPPORT=y +CONFIG_SPL=y +CONFIG_DEFAULT_DEVICE_TREE="armada-388-helios4" +CONFIG_DEBUG_UART=y +CONFIG_DISTRO_DEFAULTS=y +CONFIG_BOOTDELAY=3 +CONFIG_SYS_CONSOLE_INFO_QUIET=y +# CONFIG_DISPLAY_BOARDINFO is not set +CONFIG_DISPLAY_BOARDINFO_LATE=y +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x141 +CONFIG_SPL_I2C_SUPPORT=y +# CONFIG_CMD_FLASH is not set +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_PCI=y +CONFIG_CMD_SF=y +CONFIG_CMD_SPI=y +CONFIG_CMD_USB=y +# CONFIG_CMD_SETEXPR is not set +CONFIG_CMD_TFTPPUT=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_TIME=y +# CONFIG_SPL_PARTITION_UUIDS is not set +CONFIG_ENV_IS_IN_MMC=y +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_SPL_OF_TRANSLATE=y +CONFIG_MMC_SDHCI=y +CONFIG_MMC_SDHCI_SDMA=y +CONFIG_MMC_SDHCI_MV=y +CONFIG_AHCI=y +CONFIG_SCSI_AHCI=y +CONFIG_SCSI=y +CONFIG_SPI_FLASH=y +CONFIG_SPI_FLASH_BAR=y +CONFIG_SPI_FLASH_WINBOND=y +CONFIG_SPI_FLASH_MTD=y +CONFIG_PHY_GIGE=y +CONFIG_MVNETA=y +CONFIG_PCI=y +CONFIG_DEBUG_UART_BASE=0xd0012000 +CONFIG_DEBUG_UART_CLOCK=250000000 +CONFIG_DEBUG_UART_SHIFT=2 +CONFIG_SYS_NS16550=y +CONFIG_KIRKWOOD_SPI=y +CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_DM_I2C=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_STORAGE=y diff --git a/include/configs/helios4.h b/include/configs/helios4.h new file mode 100644 index 0000000..ce912ea --- /dev/null +++ b/include/configs/helios4.h @@ -0,0 +1,172 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright (C) 2018 Dennis Gilmore + */ + +#ifndef _CONFIG_HELIOS4_H +#define _CONFIG_HELIOS4_H + +/* + * High Level Configuration Options (easy to change) + */ + +/* + * TEXT_BASE needs to be below 16MiB, since this area is scrubbed + * for DDR ECC byte filling in the SPL before loading the main + * U-Boot into it. + */ +#define CONFIG_SYS_TCLK 250000000 /* 250MHz */ + +/* + * Commands configuration + */ + +/* SPI NOR flash default params, used by sf commands */ +#define CONFIG_SF_DEFAULT_BUS 1 + +/* + * SDIO/MMC Card Configuration + */ +#define CONFIG_SYS_MMC_BASE MVEBU_SDIO_BASE + +/* USB/EHCI configuration */ +#define CONFIG_EHCI_IS_TDI + +#define CONFIG_ENV_MIN_ENTRIES 128 + +/* + * SATA/SCSI/AHCI configuration + */ +#define CONFIG_SCSI_AHCI_PLAT +#define CONFIG_SYS_SCSI_MAX_SCSI_ID 2 +#define CONFIG_SYS_SCSI_MAX_LUN 2 +#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ + CONFIG_SYS_SCSI_MAX_LUN) + +/* Environment in MMC */ +#define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_ENV_SECT_SIZE 0x200 +#define CONFIG_ENV_SIZE 0x10000 +/* + * For SD - reserve 1 LBA for MBR + 1M for u-boot image. The MMC/eMMC + * boot image starts @ LBA-0. + * As result in MMC/eMMC case it will be a 1 sector gap between u-boot + * image and environment + */ +#define CONFIG_ENV_OFFSET 0xf0000 +#define CONFIG_ENV_ADDR CONFIG_ENV_OFFSET + +#define CONFIG_PHY_MARVELL /* there is a marvell phy */ +#define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */ + +/* PCIe support */ +#ifndef CONFIG_SPL_BUILD +#define CONFIG_PCI_MVEBU +#define CONFIG_PCI_SCAN_SHOW +#endif + +/* Keep device tree and initrd in lower memory so the kernel can access them */ +#define RELOCATION_LIMITS_ENV_SETTINGS \ + "fdt_high=0x10000000\0" \ + "initrd_high=0x10000000\0" + +/* SPL */ +/* + * Select the boot device here + * + * Currently supported are: + * SPL_BOOT_SPI_NOR_FLASH - Booting via SPI NOR flash + * SPL_BOOT_SDIO_MMC_CARD - Booting via SDIO/MMC card (partition 1) + */ +#define SPL_BOOT_SPI_NOR_FLASH 1 +#define SPL_BOOT_SDIO_MMC_CARD 2 +#define CONFIG_SPL_BOOT_DEVICE SPL_BOOT_SDIO_MMC_CARD + +/* Defines for SPL */ +#define CONFIG_SPL_SIZE (140 << 10) +#define CONFIG_SPL_TEXT_BASE 0x40000030 +#define CONFIG_SPL_MAX_SIZE (CONFIG_SPL_SIZE - 0x0030) + +#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + CONFIG_SPL_SIZE) +#define CONFIG_SPL_BSS_MAX_SIZE (16 << 10) + +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SYS_MALLOC_SIMPLE +#endif + +#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10)) +#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4) + +#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SPI_NOR_FLASH +/* SPL related SPI defines */ +#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000 +#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS +#endif + +#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SDIO_MMC_CARD +/* SPL related MMC defines */ +#define CONFIG_SYS_MMC_U_BOOT_OFFS (160 << 10) +#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_MMC_U_BOOT_OFFS +#ifdef CONFIG_SPL_BUILD +#define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER 0x00180000 /* in SDRAM */ +#endif +#endif +/* + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros + */ +#include "mv-common.h" + +/* Include the common distro boot environment */ +#ifndef CONFIG_SPL_BUILD + +#ifdef CONFIG_MMC +#define BOOT_TARGET_DEVICES_MMC(func) func(MMC, mmc, 0) +#else +#define BOOT_TARGET_DEVICES_MMC(func) +#endif + +#ifdef CONFIG_USB_STORAGE +#define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0) +#else +#define BOOT_TARGET_DEVICES_USB(func) +#endif + +#ifdef CONFIG_SATA +#define BOOT_TARGET_DEVICES_SATA(func) func(SATA, sata, 0) +#else +#define BOOT_TARGET_DEVICES_SATA(func) +#endif + +#define BOOT_TARGET_DEVICES(func) \ + BOOT_TARGET_DEVICES_MMC(func) \ + BOOT_TARGET_DEVICES_USB(func) \ + BOOT_TARGET_DEVICES_SATA(func) \ + func(PXE, pxe, na) \ + func(DHCP, dhcp, na) + +#define KERNEL_ADDR_R __stringify(0x800000) +#define FDT_ADDR_R __stringify(0x100000) +#define RAMDISK_ADDR_R __stringify(0x1800000) +#define SCRIPT_ADDR_R __stringify(0x200000) +#define PXEFILE_ADDR_R __stringify(0x300000) + +#define LOAD_ADDRESS_ENV_SETTINGS \ + "kernel_addr_r=" KERNEL_ADDR_R "\0" \ + "fdt_addr_r=" FDT_ADDR_R "\0" \ + "ramdisk_addr_r=" RAMDISK_ADDR_R "\0" \ + "scriptaddr=" SCRIPT_ADDR_R "\0" \ + "pxefile_addr_r=" PXEFILE_ADDR_R "\0" + +#include + +#define CONFIG_EXTRA_ENV_SETTINGS \ + RELOCATION_LIMITS_ENV_SETTINGS \ + LOAD_ADDRESS_ENV_SETTINGS \ + "fdtfile=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \ + "console=ttyS0,115200\0" \ + BOOTENV + +#endif /* CONFIG_SPL_BUILD */ + +#endif /* _CONFIG_HELIOS4_H */